3D Dental Printers in 2026: Choosing One and the IT Behind It
You have watched the demo. Night guards before lunch, a surgical guide the same afternoon, models without a lab bill. Then the rep asks where the printer will sit, which computer will run the software and whether the office Wi-Fi reaches that corner. Nobody at the demo mentioned a firewall.
A dental office 3D printer is a resin (SLA, DLP or LCD) printer with cleared dental materials, a wash and cure unit, a design or slicer PC and a network connection. Before you buy, decide between chairside printing, a lab and a hybrid, then give the printer a wired drop, firewall exceptions, a dedicated PC and a backed-up file location.
This guide covers both halves of that decision: which kind of printer fits a dental office, and what the printer will need from the office that the quote does not list. Every vendor fact below was read on the vendor's own page on 6 November 2026; the IT side is written from how these devices behave on a clinical network.
A dental office 3D printer is a resin (SLA, DLP or LCD) printer with cleared dental materials, a wash and cure unit, a design or slicer PC and a network connection. Before you buy, decide between chairside printing, a lab and a hybrid, then give the printer a wired drop, firewall exceptions, a dedicated PC and a backed-up file location.
- Decide in-house, lab or hybrid printing first.
- The resin's 510(k) record, not the printer, decides what you may print.
- The printer is a network device: a wired drop, its own network segment and a vendor allow-list.
- Give the slicing software a dedicated PC, never the front-desk computer.
- Print files are patient data: case IDs, one backed-up folder and a retention rule.
- Agree who handles what (vendor, reseller or IT) before the first failure.
In this guide
- Should a dental office print in-house, use a lab or do both?
- How is 3D printing applied in dentistry, and which technology do dental printers use?
- Which 3D printer fits a dental office? The systems compared
- What does the printer need from the office network?
- Which computer runs the slicer and the design software?
- Where do STL files and print jobs live, and who backs them up?
- What does same-day dentistry look like as a workflow, from scan to print?
- Why do in-office 3D printing projects stall, and what does the office need to change?
- Who do you call when a print or an update fails: the vendor, the reseller or IT?
- How do you check what a dental resin is cleared for?
- What to ask your IT provider before the printer arrives
- How Legend Networking fits in
- Frequently asked questions
- The bottom line
Should a dental office print in-house, use a lab or do both?
Print in-house when you make the same few appliances every week and someone on staff owns the machine. Send to a lab when volume is low or the work is restorative and shade-critical. Most offices land on a hybrid: models, guides and night guards in-house, crowns, dentures and aligners through a lab. The decision table below is where to start.
The question the SERP skips is the second one: what each path costs the office in people and infrastructure. A lab needs a secure way to send files. A printer needs a room, a PC, a network drop, firewall exceptions, a backup location and a person. The hybrid needs all of it, at smaller scale.
Print in-house, use a lab or run a hybrid: what each path needs from the office
| Question | Print in-house | Send to a lab | Hybrid (most offices) |
|---|---|---|---|
| Best for | Models, surgical guides, night guards, custom trays, aligner models made weekly | Low volume; definitive crowns, dentures and aligners where the lab holds the design skill | Routine appliances in-house, restorative and aligner work at the lab |
| Turnaround | Same day for most appliances; wash and cure add minutes to hours | Days to weeks, plus shipping or portal upload | Same day where it matters, lab elsewhere |
| People | A named owner for the printer: resin, tanks, calibration, software updates | Someone who sends cases correctly and tracks them | Both roles, often one person |
| Hardware | Printer, wash and cure unit, a design or slicer PC, ventilation, a resin cabinet | Scanner and a PC that can upload large files | Everything in the first column |
| Network | A wired drop or reliable Wi-Fi, internet access for cloud slicers, firewall exceptions, ideally its own VLAN | Enough upload bandwidth for scan files; a vetted portal | Both |
| Files | STL, PLY and design files stored, named without patient identifiers and backed up | Scans in the lab portal; export folders cleaned up | Both |
| Regulatory homework | You choose the resin and its indication for every appliance; the vendor's 510(k) record tells you what it is cleared for | The lab chooses materials and carries the paperwork | You carry it for whatever you print |
| Where it breaks | Printer offline, failed update, PC too weak for the slicer, files lost when a PC is replaced | Upload failures, shared portal logins, scans emailed | Both |
If you already print surgical guides from an implant planner, our guide to implant planning software computer requirements covers the planning PC and the dongle server; this page picks up at the printer.
How is 3D printing applied in dentistry, and which technology do dental printers use?
Dental 3D printing turns a digital design into a physical appliance by curing liquid resin layer by layer. The design comes from an intraoral scan or a lab file, is prepared in CAD or a slicer, printed, then washed and cured. Almost every dental office printer is a resin printer; the differences are the light source and the materials.
The FDA describes the general method on its 3D printing page: "3D printing is a process that creates a three-dimensional object by building successive layers of raw material." The same page lists dental restorations such as crowns among the devices now made this way (FDA, content current as of 12 May 2023).
In dentistry the raw material is almost always a photopolymer resin, and three light-based methods dominate:
- SLA (stereolithography): light cures a vat of resin one layer at a time. Classic SLA traces each layer with a laser; Formlabs, which sells the Form 4B and Form 4BL as its dental SLA printers, now cures each layer with a "Low Force Display" whose backlight unit uses 60 LEDs and collimating lenses.
- DLP (digital light processing): a projector exposes a whole layer at once. Asiga's Max 2 spec sheet lists "DLP" with an "Auto-calibrating UV LED" at 385 nm and a pixel size of 50 or 62 µm depending on the model.
- LCD / MSLA: an LCD mask and a UV backlight expose the layer. This is the technology inside the low-cost hobby printers that fill "best dental 3D printer" listicles; whether a given machine and resin pair is validated for a dental indication is a separate question, covered below.
Two other families exist and matter less to an office. Fused deposition (FDM) melts plastic filament and is used for study models and jigs, not appliances that touch a patient. Powder-bed methods (SLS, metal) live in labs and production centres. Labs are also where the production-scale resin platforms sit, such as Carbon's M3 series and 3D Systems' NextDent 5100.
The technology label is less important than three practical questions: which cleared resins run on the machine, how the printer connects to your network, and which software prepares the file. The rest of this guide is organised around those three.
What are the common dental 3D printing applications?
Models for aligners and retainers, surgical guides for implants, occlusal and night guards, custom impression trays, temporary crowns and bridges, denture bases and teeth, and indirect bonding trays. Vendor material catalogues name the indication on the resin: Formlabs lists Surgical Guide Resin, Dental LT Clear Resin, Denture Base Resin, Premium Teeth Resin and model resins; SprintRay's cleared materials include Digital Crown, Crown HT, Digital Temp, OnX Tough, Apex Flex, NightGuard Flex and two denture base resins (openFDA records, below).
Which 3D printer fits a dental office? The systems compared
A dental office usually chooses between a dental-dedicated chairside system (SprintRay, Formlabs Dental, Asiga, 3D Systems NextDent), a subscription production printer aimed at labs (Carbon), or a low-cost LCD printer validated by nobody for dental use. The table lists what each vendor publishes about connectivity, software and files, which is what IT needs before the box arrives.
Where a cell says "see spec sheet", the vendor page we could read on 6 November 2026 did not state it. Do not fill it in from a reseller; ask the vendor for the written spec and keep it with the purchase order.
Dental 3D printer systems compared from the IT side (vendor pages read 6 November 2026)
| System | Technology and models | Connectivity the vendor states | Software the vendor names | File inputs stated | IT note | Best for |
|---|---|---|---|---|---|---|
| SprintRay (Pro 2, Pro S, Midas, NanoPrint) | Resin; Pro 2 and Pro S desktop printers, Midas for restorative, NanoPrint as a smaller unit; NanoWash, NanoCure, ProWash S and ProCure 2 for post-processing | Wi-Fi or LAN; "The printer must be connected to the internet in order to appear in Print Setup"; a wired LAN "may be more reliable" where network security is strict | RayWare Cloud 2.0 (browser; the vendor's FAQ scheduled Cloud 1.0 for retirement in February 2025), RayWare Desktop, Print Setup, Design Suite and cloud design services | see spec sheet (RayWare documentation is behind a scripted support site) | 18 domains, IP addresses and ports to allow through the firewall (table below); same subnet for printer and PC; no guest network; the printer registers to a SprintRay account | General and restorative offices that want one vendor for printer, resin, wash, cure and design |
| Formlabs Dental (Form 4B, Form 4BL) | SLA family, cured by Formlabs' Low Force Display (an LED backlight unit, not a laser); Form 4B and the larger Form 4BL; Form Wash and Form Cure; automatic dispense resin cartridges | see spec sheet (the Form 4B page we could read does not list the ports) | PreForm (Windows 10 64-bit version 1809 or later; macOS 13 or later), Dashboard for printer fleet and notifications | see spec sheet | A PC or Mac that meets the PreForm line; Dashboard is a cloud service, so the printer needs outbound internet for fleet features | Offices and small labs that already run Macs or want an open resin library |
| Asiga (Max 2, Pro 4K) | DLP, 385 nm auto-calibrating UV LED; Max 2 at 50 or 62 µm pixel; build volume 96 × 54 × 76 mm or 119 × 67 × 76 mm | "Wifi, Wireless Direct, Ethernet" (Max 2 spec) | Asiga Composer, "Compatible on Windows, MacOS and Linux", free with lifetime updates | STL, SLC, PLY, STM | Ethernet on the spec sheet makes a wired drop easy; an open material system means the office chooses and documents the resin | Precision-focused offices and in-house labs that want an open system |
| Carbon (M3 series) | Production resin platform sold by subscription | see spec sheet; the platform is cloud-managed | Printer software "Included in your subscription with regular OTA software updates about every eight weeks" | see spec sheet | Over-the-air updates arrive on the vendor's schedule, so change control and a reliable outbound connection matter; priced "based on the hours you use your printer" | Labs and DSO production centres, not a single operatory |
| 3D Systems NextDent (NextDent 5100, NextDent 300) | Resin platforms with the NextDent material line | see spec sheet | 3D Sprint | see spec sheet | Lab-oriented; a vendor-managed PC is common | Labs and high-volume denture or model production |
| Low-cost LCD printers (brands that fill "best dental 3D printer" listicles) | LCD / MSLA hobby machines | Usually USB stick or Wi-Fi; varies by model | Third-party slicers | STL and others | No dental validation on the printer side; resin indication and clearance are on you; firmware and slicer updates are unmanaged | Study models and training, not patient appliances, unless a resin vendor validates the pairing in writing |
Two reading rules for this table. First, "see spec sheet" is not a mark against a vendor; it means the public page we could open did not state the detail, and the printed spec sheet or the installer will. Second, the right-hand column is a starting point, not a recommendation: a periodontist printing guides and a general practice printing night guards will weight the columns differently.
Best dental 3D printers compared: what to verify before you buy
"Best" lists on the web rank printers by resolution and price. For an office, the ranking that matters is operational. Verify these six items in writing before the purchase order:
- The resin, not the printer, carries the indication. Ask for the K number and the indications for use of every resin you intend to print, and check them yourself (the walkthrough is below).
- Connectivity in writing. Wired Ethernet, Wi-Fi band, and the list of domains and ports the printer needs. If the vendor cannot produce the list, expect "printer offline" tickets.
- The PC spec for the slicer and any design software, plus whether it may share a machine with the practice management software (usually not).
- Where files are stored (local PC, the printer, the vendor cloud) and whether the vendor will sign a business associate agreement if patient data crosses its service. That is a vendor fact to collect, not a legal reading to make.
- Update policy. Who installs firmware and software updates, how often they arrive, and whether you can defer them to a day without patients.
- Support path. Who you call for the printer, the resin, the software and the network, and what the warranty actually says about replacement.
What does the printer need from the office network?
A dental 3D printer is a network device with a vendor cloud behind it. Chairside printers register to an account, fetch jobs from a browser slicer, send telemetry and receive firmware over the internet. Give it a wired drop where the vendor supports one, its own VLAN with the allow-list the vendor publishes, and keep it off the guest network.
This is the section no printer review writes, and it is where most "the printer is offline" afternoons start. SprintRay's own support guide for the Pro, Pro S, Pro 2 and Midas says it plainly: "If your office network uses firewalls, content filters, or strict security rules, required connections may be blocked", and "Your IT team may need to whitelist the following URLs and ports for the printer to stay online." Its list, as published on 6 November 2026:
Domains, addresses and ports SprintRay lists for its printers to stay online (support.sprintray.com, read 6 November 2026)
| # | Endpoint | Ports | Protocol / purpose |
|---|---|---|---|
| 1 | a2oupm7fvkvi65-ats.iot.us-west-2.amazonaws.com | 443, 8883, 8443 | HTTPS / MQTT |
| 2 | *.api.sprintray.com | 443 | HTTPS |
| 3 | sr-dashboard.com | 443, 8080 | TCP / HTTPS |
| 4 | iot.sprintray.com | 443 | HTTPS |
| 5 | dashboard.sprintray.com | 443 | HTTPS |
| 6 | sprint-ray-files-prod.s3.us-west-2.amazonaws.com | 443 | HTTPS |
| 7 | iot-core.sprintray.com | 443, 8883, 8443 | HTTPS / MQTT |
| 8 | device-print.sprintray.com | 443 | HTTPS |
| 9 | 15.197.216.248 | 443, 8883, 8443 | HTTPS / MQTT |
| 10 | 3.33.208.121 | 443, 8883, 8443 | HTTPS / MQTT |
| 11 | 1.1.1.1 | ICMP | Ping / connectivity check |
| 12 | time.windows.com | 123 | UDP, NTP server |
| 13 | sprintray-device-logfile.s3.us-west-2.amazonaws.com | 443 | HTTPS |
| 14 | app.launchdarkly.com | 443 | HTTPS |
| 15 | clientstream.launchdarkly.com | 443 | HTTPS |
| 16 | events.launchdarkly.com | 443 | HTTPS |
| 17 | uas6loqlfbgjtdizihuiebbyou.appsync-api.us-west-2.amazonaws.com | 443 | HTTPS |
| 18 | ota.sprintray.com | 443 | HTTPS |
Read that list as an IT person does. Port 8883 is MQTT over TLS, the protocol smart devices use to hold an open connection to a cloud broker; a firewall that only allows web traffic on 443 will let the printer browse and still show it as offline. UDP 123 is time synchronisation; a printer with the wrong clock fails certificate checks. ICMP to 1.1.1.1 is the printer's own "am I online" test. The two raw IP addresses are the ones a hostname-only allow-list misses. And the vendor warns that "If these endpoints are blocked, the printer may intermittently appear offline", which is exactly the pattern that gets blamed on Wi-Fi.
Other vendors publish less, and the principle holds. Asiga's Max 2 lists "Wifi, Wireless Direct, Ethernet", so a wired drop is available. Carbon's M3 software is "Included in your subscription with regular OTA software updates about every eight weeks", which means a managed outbound connection and a plan for when an update lands. Formlabs' Dashboard lets you "organize printers and manage access, and get notifications when a print is finished", a cloud feature that needs the printer online.
Wired, Wi-Fi or its own VLAN? The setup we recommend
Wired wherever the printer has an Ethernet port, on a switch port assigned to a device VLAN that is separate from the clinical workstations and the server. The VLAN gets the vendor's allow-list outbound and nothing inbound from the internet. The slicer PC sits where it can reach both the printer VLAN and the clinical network, because, as SprintRay notes, "If using Wi-Fi, ensure the printer and computer are on the same subnet." If Wi-Fi is the only option, use the 5 GHz band on a dedicated SSID, never the guest network: "Avoid public guest networks, which often block device-to-device communication."
Why the separation? A printer is a computer you do not patch on your schedule, running software you cannot audit, with an open channel to a vendor cloud. That is the textbook definition of a device to segment. It also protects the printer: a clinical network with strict content filtering will otherwise block the MQTT ports above and nobody will connect the two events.
When a printer shows offline, check the printer's own connectivity screen first (SprintRay: Settings, then Connectivity; the Pro 2 and Midas include a Network Test). If the printer reaches its vendor but the slicer does not see it, sign out of the vendor account on both and sign back in with the same credentials, then wait a minute. If the printer cannot reach the vendor at all, the problem is network-side and belongs to IT, not to the printer vendor.
This is the point where the office's wider network design matters. If your switch cannot do VLANs or the firewall cannot take a per-device allow-list, the printer project becomes a network project; our guide to dental office network setup explains what a clinical network should already have before you add devices like this.
Which computer runs the slicer and the design software?
A slicer prepares the print file (orientation, supports, layer settings) and sends it to the printer; design software (exocad, 3Shape, the vendor's design suite) creates the appliance. Slicers run on modest PCs; design software needs a graphics workstation. Give the printer its own PC that meets the strictest vendor line, and keep it off the practice management software.
The vendor lines you can verify today:
Printer software and the computer it needs (vendor pages read 6 November 2026)
| Software | Vendor | Runs on | What the vendor states | IT reading |
|---|---|---|---|---|
| PreForm | Formlabs | Windows or macOS desktop | "Windows 10, 64-bit (version 1809) or later"; "macOS 13 or later, Apple Silicon" with an Intel-based Mac build available | A current Windows 11 Pro office PC qualifies; Windows 10 is past the end of Microsoft support, so plan the PC on Windows 11 |
| Asiga Composer | Asiga | Windows, macOS, Linux | "Compatible on Windows, MacOS and Linux"; free; "Lifetime updates included" | Runs on almost anything; the printer connection is the constraint, not the PC |
| RayWare Cloud 2.0 | SprintRay | Browser | The vendor's January 2025 FAQ said Cloud 1.0 "will be retired in February 2025"; "To create print jobs, all users" move to 2.0 | A browser-based slicer means the PC needs reliable internet and a supported browser, and the vendor can change the software without you installing anything |
| RayWare Desktop / Print Setup | SprintRay | Desktop application | Named on the vendor site; requirements page not readable in a script-free fetch | Ask for the written requirements; expect a 64-bit Windows machine |
| 3D Sprint | 3D Systems | Desktop application | Named on the vendor's dental page | Lab-oriented; often supplied with a vendor PC |
| Design software (exocad, 3Shape Dental System, vendor design suites) | various | Graphics workstation | Published per product and version | Not a slicer PC: see the CAD workstation guide linked below |
The practical rules:
- One PC per printer station, not the front desk. Slicers hold large mesh files in memory and talk to the printer constantly; a reception PC running the practice management software and a card reader is the wrong host.
- Design is a different machine. If the office designs guides, crowns or dentures in exocad or 3Shape, that work needs a graphics workstation with a discrete GPU and a vendor-approved spec. Our guide to dental CAD and scanner workstation requirements has the vendor lines; buy to the higher list.
- Pin versions. Slicer and firmware updates change supports, exposure and material profiles. Take them on a non-clinical day, after a test print, and note the version in the printer log. The same instinct an imaging MSP described for scanners applies here: do not update the driver stack in the first months after a working install.
- Local admin, carefully. Slicers often need to install printer drivers or USB services; give the printer owner a documented way to run those installs rather than a permanent admin account.
- Buying the PC: the general rules for office machines are in our guide on which computers to buy for a dental office; for the printer PC, add RAM headroom and an SSD large enough for a year of print files.
Where do STL files and print jobs live, and who backs them up?
Print files are patient data when they describe a patient's teeth, and they live in more places than anyone intends: the scanner PC's export folder, the design PC, the slicer's project folder, the printer's own storage, the vendor cloud and the lab portal. Name them without patient identifiers, keep them in one backed-up folder, and set a retention rule.
The formats you will see: STL (the mesh the printer slices, no colour), PLY and OBJ (meshes with colour, from intraoral scanners), DCM (DICOM volumes from CBCT, used in guide planning), and the slicer's own project files. Asiga lists its inputs as "STL, SLC, PLY, STM"; others accept STL and OBJ almost universally. A single arch scan is tens of megabytes; a CBCT volume is hundreds. A year of printing fills a desktop drive faster than a year of X-rays.
The file hygiene that keeps the office out of trouble:
Print-file hygiene for the printer station
- One folder for print files on the slicer PC, inside the office's backed-up data set, with a sub-folder per month; no files on the desktop or in Downloads.
- File names use the chart number or an internal case ID, never the patient's name or date of birth; the practice management software holds the link.
- The scanner export folder, the design PC and the slicer PC are checked monthly for stray scans and exports, and cleaned up.
- The printer's internal storage is cleared on a schedule, and before the printer is serviced, returned or sold.
- A written retention rule: how long completed case files stay, and where the long-term copy lives if the practice keeps one.
- Vendor cloud and design-service accounts are named users, not a shared login; access is removed on the day a staff member leaves.
- The backup job includes the print-file folder, and a restore of one case file has been tested in the last quarter.
Two of those points deserve a paragraph. First, cloud design services. SprintRay's Design Suite "combines AI and on-demand designers", Formlabs' Dashboard tracks printers and notifications in the cloud, and every lab portal holds scans. Each is a vendor that may receive patient data, so each is a vendor to ask about a business associate agreement before the first case is uploaded. That is a question for the vendor and, if the answer is unclear, for your compliance adviser, not a judgement this page makes. Our guide on how to send scans and STL files to the lab safely covers portals, shared logins and the export-folder cleanup in detail.
Second, backup. Most office backup jobs were scoped around the practice management database and the X-ray folder; the printer PC arrived later and sits outside them. Make sure your dental data backup covers the print-file folder, and test a restore. The same gap applies to the design workstation, as our guide to the prosthodontic digital workflow from the IT side shows with its file-flow map.
What does same-day dentistry look like as a workflow, from scan to print?
Same-day appliances are a chain of six steps across four systems: scan, design, slice, print, wash and cure, deliver. Each step has a file, a device and a network dependency. Map the chain before buying the printer and you know which PC, drop and account each step needs; skip it and you find out the first time a link fails.
Implant and prosthodontic work shows the benefit most clearly, because the chain shortens a process that used to take two visits and a courier. Here it is as the IT sees it:
Scan to appliance: the six steps and what each one needs
- 1Scanthe intraoral scanner captures the arch as PLY or STL on the scanner's own PC or cartNeeds: a scanner PC that meets the vendor's spec, Wi-Fi or wired upload to the scanner vendor's cloud or a local export folder.
- 2Designthe clinician or a designer builds the appliance in CAD (exocad, 3Shape, a vendor design suite or a cloud design service)Needs: a graphics workstation or a browser and an account; the design file and the scan now exist in a second place.
- 3Slicethe slicer orients the design, adds supports and prepares the job for the printerNeeds: the slicer PC, the material profile for the exact resin, the right printer selected on the network.
- 4Printthe job reaches the printer over the network or the vendor cloud and printsNeeds: printer online (allow-list, subnet, account), resin loaded, tank and platform within life.
- 5Wash and curethe part is washed, dried and post-cured in the vendor's unitsNeeds: space, ventilation, the cure profile for the resin; no network, but the step is where under-cured parts come from.
- 6Deliver and recordthe appliance is finished, fitted and the case is recordedNeeds: the case file archived under its ID in the backed-up folder; the printer and PC storage cleared on schedule.
The chain explains why the printer is rarely the weak link. Scanner uploads fail on thin Wi-Fi (our guide to intraoral scanner IT requirements has the vendor network rules). Design stalls on a PC with integrated graphics. Slicing stalls when the profile for a new resin has not been downloaded. Printing stalls on a blocked port. The appliance is late, and the printer is blamed.
Why do in-office 3D printing projects stall, and what does the office need to change?
Projects stall for the same reasons they did five years ago: the software has a learning curve, nobody owns the machine, and the office adds printing to an existing day without changing anything else. The fix is a named owner, protected time in the first month, written procedures for resin and files, and IT finished before the printer arrives.
The live version of this page said it in 2023: adoption lagged because clinicians were slow to learn the design software, and because printing "requires a new work logic". That is still true, and the list is longer now:
- Ownership. A printer with no owner runs out of resin, misses tank changes and falls behind on updates. Assign one person and a deputy.
- Training time. Block the first month's training against the schedule; a slicer learned between patients is learned badly.
- Procedures. Write down the resin, the profile, the wash and cure times and the file naming for each appliance you make. Vendors publish appliance design guidelines; adopt them as the office's own.
- IT before delivery. The drop, the VLAN, the allow-list, the PC and the backup job should be done the week before, not the week after.
- Vendor support reality. Owners are candid about this. One practice owner wrote in January 2026 that a printer bought "less than a year ago" became "completely non-functional due to a software update failure" after "3 over-the-air update attempts" and "3 hard resets", and that the vendor had taken "no steps toward replacement" despite a first-year promise (r/Dentistry thread 1qj696q, snapshot 21 January 2026). Another user in the same thread reported the opposite experience with the same vendor. The lesson is not which vendor to pick; it is to get the warranty terms, the escalation path and the update policy in writing, and to have your own IT provider in the loop so a network problem is never mistaken for a hardware one.
- Cost realism. Printer quotes list the printer, the wash and cure units and starter resin. They rarely list the PC, the network work, the ventilation, the staff time or the downtime of a failed update. Budget those lines yourself. If the purchase falls in the tax year, our note on Section 179 and dental IT equipment explains the timing question to raise with your CPA.
Who do you call when a print or an update fails: the vendor, the reseller or IT?
Call the resin or printer vendor for print quality, materials and hardware faults; the reseller for warranty and replacement; the software vendor for slicer or design-software errors; and your IT provider for anything involving the network, the PC, accounts, files or backups. Decide this map before the first failure and write it on the printer station.
Who owns the problem: printer, software, reseller or IT
| Symptom | Likely layer | First owner | What IT checks first |
|---|---|---|---|
| Printer shows offline in the slicer but the printer screen says connected | Account sync or cloud reachability | IT, then the printer vendor | Vendor allow-list on the firewall, DNS, time sync (NTP), same subnet; sign out and in |
| Printer cannot connect to the network at all | Network | IT | Switch port and VLAN, DHCP lease, Wi-Fi SSID and band, cable |
| Printer connected, slicer cannot upload or the job never starts | Slicer PC or cloud service | Software vendor, with IT | PC on the same subnet, browser version, blocked ports (443, 8883, 8443, 8080), vendor status |
| Firmware or software update failed and the printer will not recover | Hardware or vendor software | Printer vendor and reseller (warranty) | Collect logs and screenshots the vendor asks for; confirm the network was not the cause so the warranty claim stands |
| Prints fail, warp or under-cure | Materials, calibration, profile | Resin and printer vendor | Nothing network-side; confirm the slicer profile matches the resin version |
| Design software crashes or runs slowly | Workstation spec or licence | Software vendor and IT | GPU, RAM, licence or dongle server reachability |
| A case file is missing after a PC change | Files and backup | IT | Backup scope, restore from backup, export-folder search on the old disk |
| Lab or cloud design upload fails | Internet or portal | IT, then the portal vendor | Upload bandwidth, firewall, file size, portal status |
Two habits make the map work. Keep a printer log (date, firmware version, slicer version, resin lot, tank age, each failure and fix) so the vendor conversation starts from facts, and have IT confirm the network before you open a hardware ticket, because a vendor will ask and a warranty claim is stronger when the answer is already documented. If X-ray sensors are also on your list this year, our buyer's guide to dental X-ray sensors uses the same vendor-or-IT split.
How do you check what a dental resin is cleared for?
Look the resin up in FDA's public 510(k) database by vendor name, read the device name and decision date, and open the record for the indications for use. The record says what the material is cleared to make; the printer page says what it can make. Those are different lists, and the first governs what you print for a patient.
This is not legal advice and this page does not interpret the regulations; the FDA's own 3D printing page says "Medical device manufacturers should refer to FDA guidance documents". What an office can do is read the public record. Using the openFDA 510(k) database on 6 November 2026, a search by applicant returned:
510(k) records by applicant in the openFDA database (queried 6 November 2026; check the live record before relying on it)
| Applicant | Records found | Examples (K number, decision date, device name) |
|---|---|---|
| SprintRay | 9 | K260661 (15 April 2026) Midas Restore · K250617 (29 April 2025) Apex Flex · K242559 (26 November 2024) Digital Temp · K242277 (1 October 2024) Crown HT · K230445 (14 July 2023) OnX Tough · K222623 (14 December 2022) Digital Crown · K221678 (10 November 2022) SprintRay High Impact Denture Base · K220979 (14 September 2022) SprintRay Denture Base · K212448 (12 November 2021) NightGuard Flex |
| Formlabs | 4 | K262300 (8 July 2026) Denture Base Resin V2 · K240538 (19 July 2024) Premium Teeth Resin · K232087 (16 February 2024) Dental LT Comfort Resin · K222061 (10 November 2022) Dental LT Clear V2 Resin |
| Asiga | 2 | K243370 (5 May 2025) DentaTOOTH · K243356 (11 April 2025) Asiga DentaBASE |
How to read it: the search is by applicant, so resins cleared under a material partner's name (BEGO, Dentsply Sirona, Keystone and others whose materials run on these printers) appear under that partner, not the printer brand. Many model, guide and tray resins are also marketed with other regulatory statuses rather than a 510(k). None of that is a mark for or against a vendor; it is the homework that puts the right material behind each appliance. Ask the vendor for the record for each resin you plan to use, and keep the printout with the purchase file.
What to ask your IT provider before the printer arrives
Ask before the purchase order, not after delivery: whether the printer gets a wired port on its own VLAN, whether the firewall takes the vendor's allow-list, which PC runs the slicer, where print files are backed up, who installs updates and who answers first when the printer shows offline. The answers decide whether the printer works on day one.
What to ask your IT provider
- Can you put the printer on a wired port in its own VLAN, with the vendor's allow-list outbound and nothing inbound?
- Does our firewall handle the vendor's domains, raw IP addresses and the non-web ports (8883, 8443, 8080, UDP 123), and will you document the rule?
- Which PC will run the slicer, does it meet the vendor's requirements, and will it stay off the practice management software?
- If we design in-house, which workstation runs exocad or 3Shape, and what is its approved spec?
- Where will print files live, are they inside the backup job, and when did we last test a restore?
- Who installs firmware and slicer updates, on which day, and how do we roll back a bad one?
- How do we remove a departing staff member from the vendor cloud, design service and lab portal on the same day?
- Who do we call first when the printer shows offline, and what will you check before we open a vendor ticket?
What to ask the printer vendor or reseller
- The written network requirements: ports, domains, IP addresses, Wi-Fi bands, Ethernet availability.
- The written PC requirements for every piece of software in the bundle.
- The 510(k) record and indications for use for every resin in the quote.
- Whether patient data touches the vendor's cloud or design service, and whether the vendor signs a business associate agreement.
- The update policy: frequency, whether updates can be deferred, and what happens when one fails.
- The warranty's actual replacement terms, the escalation path and the support hours, in writing.
How Legend Networking fits in
Legend Networking has served over 3,500 practices since 2004. The IT environment around a 3D printer is the same one we build for imaging: workstations, network, firewall, backup and the accounts behind them. We support the IT environment for DEXIS, Vatech, Carestream, Planmeca/Romexis and Dolphin Imaging, and the printer station plugs into that same network design.
What that looks like in practice: a wired drop and a device VLAN for the printer, the vendor's allow-list on the firewall, a slicer PC specified to the vendor's line and kept separate from the practice management software, the print-file folder inside the backup job, and 24/7 monitoring on the network the printer depends on. In-house engineers; no outsourced first-level triage, so when a printer shows offline the person on the call can read the firewall log rather than ask you to reboot.
Ian Lynch — 22 years in dental IT; oversees the NOC, onsite dispatch and client technology roadmaps — is the author of this guide, and a printer station belongs on that roadmap. Legend's project pages include the November 2025 opening of Hallmark Prosthodontics in Pearland, Texas, a specialty where printing and design sit at the centre of the workflow. Practices rate Legend 4.8 from 173 Google reviews.
If the printer is one of several devices arriving this year, start with the environment they all share. Our dental practice management software support page describes the IT around the software and imaging the printer feeds from, dental servers and workstations covers the PCs, and managed IT services for dental practices is the monthly arrangement under which the printer station, the firewall rules and the backup job are looked after together. Practices in North Texas can also read about dental IT in Dallas, where Legend's headquarters and NOC are. Office paper printers are a different problem; if that is the one that is down, our dental office printer not printing guide has the front-desk fixes.
Frequently asked questions
What 3D printer should a dental office buy?
Buy a dental-dedicated resin system whose cleared materials match the appliances you make most, whose vendor publishes its network and PC requirements in writing, and whose support and warranty terms you have read. SprintRay, Formlabs Dental, Asiga and 3D Systems NextDent are the common office and lab systems; low-cost LCD printers lack dental validation on the printer side.
Does a dental 3D printer need to be connected to the internet?
Most current chairside printers do. SprintRay's support guide says the printer "must be connected to the internet in order to appear in Print Setup", and cloud slicers, fleet dashboards and firmware updates all rely on an outbound connection. The office firewall then needs the vendor's allow-list of domains and ports, or the printer appears offline intermittently.
Should the 3D printer be on Wi-Fi or a wired connection?
Wired, where the printer has an Ethernet port (Asiga lists Ethernet; SprintRay says a wired LAN "may be more reliable" on strictly secured networks). Place it on its own VLAN with the vendor's allow-list. If Wi-Fi is the only option, use a dedicated 5 GHz SSID on the same subnet as the slicer PC, and never the guest network.
Why does my dental 3D printer keep showing offline?
Usually because the firewall or content filter blocks one of the vendor's endpoints or non-web ports (MQTT on 8883 or 8443, NTP on UDP 123), because the printer and the slicer PC sit on different subnets, or because the printer and the slicer are signed into different vendor accounts. Check the printer's connectivity screen, then the allow-list, before opening a hardware ticket.
What computer do I need for a dental 3D printer?
A dedicated PC for the slicer that meets the vendor's line (Formlabs' PreForm: Windows 10 64-bit version 1809 or later, or macOS 13 or later; Asiga Composer runs on Windows, macOS and Linux), with an SSD large enough for a year of print files and no practice management software on it. Design software such as exocad or 3Shape needs a separate graphics workstation.
Are STL files patient data?
When a scan or design describes an identifiable patient's teeth, treat the file as patient data: store it in a backed-up folder, name it with a case ID rather than a name, clean up export folders, and ask any cloud design service or lab portal that receives it whether it signs a business associate agreement. Whether a specific file is regulated is a question for your compliance adviser.
How do I know what a dental resin is FDA cleared for?
Search the public 510(k) database by the resin vendor's name and open the record for the device name, decision date and indications for use. On 6 November 2026 openFDA listed nine records for SprintRay, four for Formlabs and two for Asiga. Resins sold under a material partner's name appear under that partner. Keep the record with your purchase file.
Who fixes a dental 3D printer when a print fails?
It depends on the layer. Print quality, materials and hardware faults go to the resin and printer vendor; warranty and replacement to the reseller; slicer or design-software errors to the software vendor; network, PC, account, file and backup problems to your IT provider. Have IT confirm the network first so a vendor ticket and any warranty claim start from documented facts.
What is the difference between dental 3D printing and a dental printer?
In search, "dental printer" can mean either a resin 3D printer that makes appliances or the office laser printer that prints statements and labels. Dental 3D printing is the first: curing resin layer by layer from a digital design. If your problem is a paper or label printer that has stopped, our dental office printer troubleshooting guide covers it instead.
How much does a 3D printer for a dental office cost?
Vendors quote printers, wash and cure units and materials, and prices change often, so this page does not list them. Budget the lines the quote leaves out: the slicer PC, a design workstation if you design in-house, network work (a wired drop, a VLAN, firewall rules), ventilation, backup capacity, staff training time and the downtime of a failed update.
The bottom line
Buy the printer for the appliances you make weekly, then give it what the quote leaves out: a wired drop, firewall exceptions, its own PC and a backed-up folder.

